Show simple item record

dc.contributor.advisorPoirier, David R.en_US
dc.contributor.authorZhang, Bin
dc.creatorZhang, Binen_US
dc.date.accessioned2013-04-11T08:54:24Z
dc.date.available2013-04-11T08:54:24Z
dc.date.issued2002en_US
dc.identifier.urihttp://hdl.handle.net/10150/280228
dc.description.abstractEffects of pore, secondary dendrite arm spacings (SDAS ), hot isostatic pressing (Hipping), and strontium-modification on fatigue behavior were studied in an aluminum casting alloy (A356.2). Microstructures were revealed by X-ray radiography, light microscopy and scanning electron microscopy. Small-cracks were monitored by taking replicas of the surfaces with which the cracks intersected. As the SDAS increases from 15 to 55 μm, fatigue life decreases by a factor of 3 in low-cycle fatigue, and 100 in high-cycle fatigue. When SDAS is less than 30 mum, the pore size is below a critical size of ∼80 μm and large eutectic constituents initiate cracks; and the initiation life is as high as 70% of the fatigue life. As the SDAS increases beyond 30 μm, pores are the main crack-initiation sites; the initiation life is as low as 5% of the fatigue life. Near-surface oxides initiate the fatigue crack regardless of SDAS. When crack initiated at pore and oxides, fatigue life is well correlated with the size of the initiation site and the effect of SDAS is overshadowed by the effect of pore. Non-hipped A356.2 without Sr shows better fatigue life and the deleterious effect of pores overshadowed the beneficial effect that Sr-modification might have had. Hipping significantly increased the initiation life and small-crack propagation life of A356.2 with Sr as a result of the elimination of the porosity. However, hipping did not significantly improve the fatigue life of A356.2 without Sr. After hipping, Sr-modification is beneficial in improving the crack initiation life, and increasing both small-crack and long-crack propagation lives. Fracture mechanics models (Newman-Raju, and Trantina-Barishpolsky models) yielded similar results on the crack-propagation rate against the effective stress-intensity factor range. In the micro-mechanics model, the theory of continuously distributed dislocations was applied to represent crack and crack-tip plastic zone, and the propagation rate was related to the length of the crack-tip plastic zone. When the grain size is used as the characteristic length of the microstructures, the model predicts the oscillations of the propagation rates and the predicted rates agreed reasonably well with those from experiments.
dc.language.isoen_USen_US
dc.publisherThe University of Arizona.en_US
dc.rightsCopyright © is held by the author. Digital access to this material is made possible by the University Libraries, University of Arizona. Further transmission, reproduction or presentation (such as public display or performance) of protected items is prohibited except with permission of the author.en_US
dc.subjectEngineering, Metallurgy.en_US
dc.subjectEngineering, Materials Science.en_US
dc.titleFatigue behavior in an aluminum casting alloy (A356.2): Effects of some defects, SDAS, Hipping and strontium modificationen_US
dc.typetexten_US
dc.typeDissertation-Reproduction (electronic)en_US
thesis.degree.grantorUniversity of Arizonaen_US
thesis.degree.leveldoctoralen_US
dc.identifier.proquest3073279en_US
thesis.degree.disciplineGraduate Collegeen_US
thesis.degree.disciplineMaterials Science and Engineeringen_US
thesis.degree.namePh.D.en_US
dc.identifier.bibrecord.b43479315en_US
refterms.dateFOA2018-09-05T09:29:41Z
html.description.abstractEffects of pore, secondary dendrite arm spacings (SDAS ), hot isostatic pressing (Hipping), and strontium-modification on fatigue behavior were studied in an aluminum casting alloy (A356.2). Microstructures were revealed by X-ray radiography, light microscopy and scanning electron microscopy. Small-cracks were monitored by taking replicas of the surfaces with which the cracks intersected. As the SDAS increases from 15 to 55 μm, fatigue life decreases by a factor of 3 in low-cycle fatigue, and 100 in high-cycle fatigue. When SDAS is less than 30 mum, the pore size is below a critical size of ∼80 μm and large eutectic constituents initiate cracks; and the initiation life is as high as 70% of the fatigue life. As the SDAS increases beyond 30 μm, pores are the main crack-initiation sites; the initiation life is as low as 5% of the fatigue life. Near-surface oxides initiate the fatigue crack regardless of SDAS. When crack initiated at pore and oxides, fatigue life is well correlated with the size of the initiation site and the effect of SDAS is overshadowed by the effect of pore. Non-hipped A356.2 without Sr shows better fatigue life and the deleterious effect of pores overshadowed the beneficial effect that Sr-modification might have had. Hipping significantly increased the initiation life and small-crack propagation life of A356.2 with Sr as a result of the elimination of the porosity. However, hipping did not significantly improve the fatigue life of A356.2 without Sr. After hipping, Sr-modification is beneficial in improving the crack initiation life, and increasing both small-crack and long-crack propagation lives. Fracture mechanics models (Newman-Raju, and Trantina-Barishpolsky models) yielded similar results on the crack-propagation rate against the effective stress-intensity factor range. In the micro-mechanics model, the theory of continuously distributed dislocations was applied to represent crack and crack-tip plastic zone, and the propagation rate was related to the length of the crack-tip plastic zone. When the grain size is used as the characteristic length of the microstructures, the model predicts the oscillations of the propagation rates and the predicted rates agreed reasonably well with those from experiments.


Files in this item

Thumbnail
Name:
azu_td_3073279_sip1_m.pdf
Size:
6.383Mb
Format:
PDF

This item appears in the following Collection(s)

Show simple item record