• Dish-based CPV-T for rooftop generation

      Davila-Peralta, Christian; Hyatt, Justin; Alfred, Dan; Struble, Morgan; Sodari, Frank; Angel, Roger; Univ Arizona, Steward Solar Lab (AMER INST PHYSICS, 2017)
      Hybrid CPV-T with combined electrical and thermal output is well suited to solar generation from fixed limited areas, such as on the roof of an industrial or commercial facility with need for heat. This application will become especially attractive once overall electrical conversion efficiency of 40% is reached, as is projected for REhnu CPV systems using multijunction cells of 50% efficiency, anticipated in a few years. We outline here a configuration of dishbased CPV trackers optimized for close packing on a flat roof in a triangular grid, with a mirror area-to-ground area ratio of 50%. When the geometry of shadowing averaged over a year is taken into account, 80% of all the sunlight that would strike the rooftop is directed into the receivers. Such an array on a given area of flat roof will generate more electrical energy than would be possible with conventional PV panels, even if covering the entire rooftop, because of silicon's relative inefficiency. For example, in Tucson, the annual average global flux of 5.7 kWh/m2/day on a horizontal surface covered with 22% silicon modules will yield 1.25 kWh/m2/day. We show that a CPV system collecting 80% of all the direct sunlight of 7.0 kWh/m2 and converting it with 40% efficiency will yield 2.24 kWh/m2/day of rooftop area, nearly twice as much4. Thermal power will double again the total energy yield A dual axis CPV-T tracker designed specifically very close spacing has been built to carry a single dish mirror of the standard type used in REhnu's M-8 generator, described by Stalcup et al in these proceedings1,2. Sunlight is collected and focused by a single square paraboloidal mirror, 1.65 x 1.65 m with focal length of 1.5 m. For closest possible packing without mechanical interference, and for broad distribution of load on a rooftop, the mirror and receiver are mounted to a C-ring structure, configured such that the elevation and azimuth axes intersect at a virtual pivot, at the center of the sphere that just clears the receiver and the corners of the mirror. Initial tests of closed loop tracking show an accuracy of 0.03 degrees rms under calm conditions, and 0.04 degrees rms in 6 m/sec wind.
    • On-grid performance of REhnu’s 8-mirror CPV-T tracker

      Stalcup, Thomas; Angel, Roger; Geary, Andrew; Sodari, Frank; Rademacher, Matt; Whiteside, Andy; Will, John; Didato, Nick; Strittmatter, Peter; Univ Arizona, Steward Observ (AMER INST PHYSICS, 2017-09)
      REhnu has built and tested two 6 kW CPV-T trackers using dish-receiver architecture. In these trackers, only the light collection elements are large, namely mirrors on dual axis trackers. The inherently small parts, the multijunction cells, are packaged in a small, inexpensive receiver at each mirror focus. Optics in the receiver apportion the intensely focused sunlight equally to many cells, for high optical efficiency and simplified manufacture. Heat is removed by recirculated liquid. The tracker carries eight 2.7 m(2) mirrors and receivers. The CSTC DC efficiency of the individual mirror receiver units is measured at 32.5%. When used for electrical generation alone, the tracker system delivers an AC electrical output of 6.27 kW to the grid, referenced to a solar flux of 1 kW/m(2) DNI and 20 degrees C ambient temperature, corresponding to a total CSOC system efficiency of 29.1%, matching the best grid-connected system efficiency reported for any CPV system4. When used to generate also a thermal output of 9 kW at 64 degrees C, the electrical efficiency of the tracker was reduced by 0.8%, while the total efficiency, thermal plus electrical, rose to 77%.